Tag: statistics

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1739448. Online ahead of print.

ABSTRACT

OBJECTIVE: SARS-CoV-2 can be carried by aerosols and droplets produced during dental procedures, particularly by the use of high-speed handpieces, air-water syringes, and ultrasonic scalers. High-volume evacuators (HVEs) and extraoral vacuum aspirators (EOVAs) reduce such particles. However, there is limited data on their efficacy. This study aimed to determine the efficacy of HVE and EOVA in reducing aerosols and droplets during ultrasonic scaling procedures.

MATERIALS AND METHODS: Three ultrasonic scaling simulations were conducted on mannequins: 1. saliva ejector (SE) was used alone (control); 2. SE was used in combination with HVE; and 3. SE was used in combination with HVE and EOVA. Paper filters were placed on the operator’s and assistant’s face shields and bodies, and the contamination of aerosols and droplets was measured by counting blue spots on the paper filters.

STATISTICAL ANALYSIS: All data were analyzed for normality using the Kolmogorov-Smirnov test. The differences between each method were analyzed using a two-way ANOVA, followed by a posthoc test. The differences were considered statistically significant when p < 0.05 RESULT: Using HVE and EOVA reduced aerosols and droplets better than using SE alone or SE and HVE: the posthoc test for contamination revealed a significant difference (p < 0.01). The assistant was subjected to greater contamination than the operator during all three ultrasonic scaling procedures.

CONCLUSION: The usage of HVE and EOVA significantly reduced aerosols and droplets compared with using SE solely. Using these techniques together could prevent the transmission of airborne disease during dental cleanings, especially COVID-19. Further studies of aerosol-reducing devices are still needed to ensure the safety of dental workers and patients.

PMID:35016239 | DOI:10.1055/s-0041-1739448

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1739449. Online ahead of print.

ABSTRACT

OBJECTIVE: This study aimed to analyze, evaluate, and characterize novel cement-based carboxymethyl chitosan/amorphous calcium phosphate (CMC/ACP).

MATERIALS AND METHODS: The three cement groups studied were gypsum (Gyp), and CMC/ACP-gypsum cement-based 5% (5% CAG) and 10% (10% CAG). The groups were characterized using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), setting time, and scanning electron microscopy (SEM) data. The characterization results were analyzed qualitatively, but the data for setting time were analyzed using SPSS (p < 0.05).

STATISTICAL ANALYSIS: Data were statistically analyzed. One-way analysis of variance was used to compare numerical (parametric) data between more than two separate groups followed by post hoc Tukey.

RESULTS: FTIR showed phosphate groups indicate the presence of calcium phosphate in the form of amorphous (ACP) in the CMC/ACP, CMC/ACP post-milled powder, and CMC/ACP cement-based (5% CAG and 10% CAG). XRD showed no difference in the diffraction spectra among the Gyp, 5% CAG, and 10% CAG groups. SEM images revealed that the CMC/ACP cement-based groups (5% CAG and 10% CAG) showed CMC/ACP cluster filled with hollow spaces between the gypsum crystals and aggregations surrounding the gypsum crystals. The CMC/ACP showed envelopes and attached to the crystalline structures of the gypsum. Setting times of 5% CAG and 10% CAG showed significant differences compared with Gyp (p < 0.05).

CONCLUSION: The result of our study showed that CMC/ACP cement-based (5% CAG and 10% CAG) demonstrated amorphous characteristic, which can stabilize calcium ions and phosphate group (ACP). In addition, the modification of gypsum using CMC/ACP as cement-based extended the time of setting.

PMID:35016237 | DOI:10.1055/s-0041-1739449

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1739440. Online ahead of print.

ABSTRACT

OBJECTIVE: This study compared the ProTaper Next (PTN; Dentsply Sirona, Tulsa, Oklahoma, United States) and HyFlex EDM (HEDM; Coltene/Whaledent AG, Alstätten, Switzerland) systems using micro-computed tomography (CT).

MATERIALS AND METHODS: Twenty-one mesial roots classified as Vertucci’s type IV from extracted mandibular first molars with curvatures between 20 and 40 degrees were selected. The teeth were scanned using a micro-CT before and after root canal preparation by both systems, applied to the same root, in alternating canals. The following parameters were analyzed: canal centering, apical transportation, root canal diameter/root diameter.

RESULTS: No statistically significant differences between both systems were observed for any of the assessed morphological parameters (p > 0.05). All canals presented diameter enlargement of more than 40% in relation to root diameter in the cervical and middle segments. No statistically significant difference was noted between the HEDM and PTN groups. The wear percentage for the HEDM group in the cervical and middle thirds were 49.66 ± 8.65 and 46.48 ± 14.29, respectively, and 51.02 ± 11.81 and 45.48 ± 10.79 for the PTN group, respectively.

CONCLUSION: Both systems displayed similar mandibular molar mesial canals preparation, with no differences noted for any of the assessed parameters. Both groups showed increased canal diameter in the cervical and middle thirds by more than 40%.

PMID:35016238 | DOI:10.1055/s-0041-1739440

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1735931. Online ahead of print.

ABSTRACT

OBJECTIVE: Antibiotics misuse and a high level of antibiotics resistance is observed worldwide, but particularly in developing countries. Kosovo in the last decade is facing challenges regarding antimicrobial resistance. The purpose of the present study was to investigate patterns of antibiotics prescriptions of dentists in Kosovo’s major dental clinics.

MATERIALS AND METHODS: For Kosovo’s prescribing pattern, data collection was obtained from 10 Regional Dental Clinics and a Tertiary Health Center regarding patients who were prescribed antibiotics in the years 2015 to 2019. Data analysis was performed by using descriptive statistics and was processed by using MS Excel.

RESULTS: Most prescribed antibiotic during the observed period from 2015 to 2019 in Kosovo was amoxicillin, although a drastic increase of amoxicillin with clavulanic acid-as a broad-spectrum antibiotic-is observed. The trend of antibiotics use in tertiary health institutions is in an overall decrease in Kosovo with an exception in the year 2017. Despite this overall decrease, inconsistency in prescribing is observed when the pattern is analyzed for each region separately. The highest number of patients in health care dental clinics received antibiotics for maxilla-related health conditions and the lowest number of them for oncologic ones.

CONCLUSION: The patterns of antibiotics prescriptions by dental practitioners in Kosovo during the years 2015 to 2019 are fluctuating. Compared with the global health care standards, the irrational use of antibiotics in dental health care clinics in Kosovo still exist and this issue should be further addressed by respective actors.

PMID:35016236 | DOI:10.1055/s-0041-1735931

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1739450. Online ahead of print.

ABSTRACT

OBJECTIVE: The aim of this study was to determine the relationship of malocclusion with the presence and severity of temporomandibular disorders (TMDs) in children.

MATERIALS AND METHODS: A clinical examination was performed in 87 patients (from 4 to 14 years of age) who attended the dentistry clinics of Universidad del Valle.

RESULTS: The 77 patients studied had malocclusions; 55 patients had TMD and 67.3% were female. The most frequent symptom of TMD was articular unilateral noise with 33.8%, followed by pain in at least one masticatory muscle with 26%. TMJ pain was observed in 24.7% of the patients. There was a statistically significant relationship between the presence and severity of TMD with type of dentition and transverse malocclusion, respectively.

CONCLUSION: The presence of TMD in children with malocclusion presented in a high frequency. TMD depends on the type of dentition and its severity is dependent on transverse malocclusion.

PMID:35016235 | DOI:10.1055/s-0041-1739450

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1735937. Online ahead of print.

ABSTRACT

OBJECTIVE: Different post-sintering processes are expected to be a reason for alteration in the strength of zirconia. This study evaluated the effect of post-sintering processes on the flexural strength of different types of monolithic zirconia.

MATERIALS AND METHODS: A total of 120 classical- (Cz) and high-translucent (Hz) monolithic zirconia discs (1.2 mm thickness and 14 mm in Ø) were prepared, sintered, and randomly divided into four groups to be surface-treated with (1) as-glazed (AG); (2) finished and polished (FP); (3) finished, polished, and overglazed (FPOG); and (4) finished, polished, and heat-treated (FPHT) technique (n = 15). Biaxial flexural strength (σ) was determined on a piston-on-three ball in a universal testing machine at a speed of 0.5 mm/min.

STATISTICAL ANALYSIS: Analysis of variance, and post hoc Bonferroni multiple comparisons were determined for significant differences (α = 0.05). Weibull analysis was applied for survival probability, Weibull modulus (m), and characteristic strength (σ₀). The microstructures were examined with a scanning electron microscope and X-ray diffraction.

RESULTS: The mean ± standard deviation value of σ (MPa), m, and σ₀ were 1,626.43 ± 184.38, 9.51, and 1,709.79 for CzAG; 1,734.98 ± 136.15, 12.83, and 1,799.17 for CzFP; 1,636.92 ± 130.11, 14.66, and 1,697.63 for CzFPOG; and 1,590.78 ± 161.74, 10.13, and 1,663.82 for CzFPHT; 643.30 ± 118.59, 5.59, and 695.55 for HzAG; 671.52 ± 96.77, 3.28, and 782.61 for HzFP; 556.33 ± 122.85, 4.76, and 607.01 for HzFPOG; and 598.36 ± 57.96, 11.22, and 624.89 for HzFPHT. The σ was significantly affected by the post-sintering process and type of zirconia (p < 0.05), but not by their interactions (p > 0.05). The Cz indicated a significantly higher σ than Hz. The FP process significantly enhanced σ more than other treatment procedures.

CONCLUSION: Post-sintering processes enabled an alteration in σ of zirconia. FP enhanced σ, while FPOG and FPHT resulted in a reduction of σ. Glazing tends to induce defects at the glazing interface, while heat treatment induces a phase change to tetragonal, both resulted in reducing σ. Finishing and polishing for both Cz and Hz monolithic zirconia is recommended, while overglazed or heat-treated is not suggested.

PMID:35016234 | DOI:10.1055/s-0041-1735937

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1739447. Online ahead of print.

ABSTRACT

OBJECTIVE: Canine impaction is a difficult condition to treat, and it usually necessitates a combination of surgical exposure and orthodontic traction or surgical extraction. An accurate assessment of the maxillary canine’s position can help determine the severity of the impaction, the difficulty of therapy, and the treatment’s prognosis.

MATERIALS AND METHODS: A total of 55 impacted canines were studied and selected retrospectively. Difficulty indexes were used to measure the severity of impaction with pretreatment panoramic radiographs.

STATISTICAL ANALYSIS: Pearson correlation was used to test the validity of the difficulty index modification score. Regression statistical analysis was used to evaluate any correlation between total scoring from each index with surgical treatment.

RESULTS: The validity test on the variable modification index score showed a valid value (p = 0.000). According to both treatment difficulty and modification index, odontectomy group showed higher mean of total scoring than surgical exposure group. Treatment difficulty and modification index showed a significant correlation with surgical treatment (p = 0.003 and p = 0.001).

CONCLUSIONS: The higher the severity of canine impaction, the greater is the possibility of odontectomy than surgical exposure. Both indexes can consider to be used in determining surgical treatment planning.

PMID:35016233 | DOI:10.1055/s-0041-1739447

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1739438. Online ahead of print.

ABSTRACT

OBJECTIVE: To evaluate and compare the first tooth contact region, occlusion time, time to generate total force, and force distribution between open bite (OB) and non-OB (NOB) patients at the maximum intercuspation position using the T-Scan III system.

MATERIALS AND METHODS: Sixteen patients were divided into the OB and NOB groups (n = 8 for each group). The T-Scan III system was used to evaluate the first tooth contact region, occlusion time, time to generate total force, and force distribution.

STATISTICAL ANALYSIS: The mean patient age, overjet, overbite, occlusion time, and time to generate total force were compared between the groups by independent samples t-test. Relative force distributions between groups and among regions were compared by the Mann-Whitney U- and Kruskal-Wallis H-tests, respectively. A probability value of less than 5% (p < 0.05) was considered significant.

RESULTS: Differences in the first tooth contact region between groups were observed. The molar region was the first tooth contact region in the OB group, while first tooth contact was observed in all regions in the NOB group. Neither the occlusion time nor the time to generate total force was significantly different between the groups (p > 0.05). The highest force distributions were observed in the molar regions in both groups. Significant intragroup differences were found among all regions (p < 0.05), except between the anterior and premolar regions in the NOB group (p = 0.317). Intergroup differences in the force distributions in the anterior (p = 0.000), premolar (p = 0.038), and molar (p = 0.007) regions were significant.

CONCLUSION: Unlike in the NOB group, in which first tooth contact occurred in every region, in the OB group, first tooth contact occurred only in the molar region. Compared with those in the NOB group, the force distributions in the OB group were approximately 1.5 times higher in the molar region but were significantly lower in the anterior and premolar regions.

PMID:35016230 | DOI:10.1055/s-0041-1739438

Eur J Dent. 2022 Jan 11. doi: 10.1055/s-0041-1736418. Online ahead of print.

ABSTRACT

OBJECTIVES: The use of herbal dentifrices has grown exponentially over the years. They are categorically referred to as ethnomedicines. Various agents have been tried with contradicting findings based on phytopharmacological analysis. Miswak is one agent which has been used over the years. A novel Moringa oleifera-based dentifrice has shown promising results in terms of its cytotoxicity, biocompatibility, and as a potent anti-inflammatory agent. Therefore, the present study aims to compare the efficacy of two commercially available miswak- and moringa-based herbal dentifrices on the reduction of plaque and gingivitis scores.

MATERIALS AND METHODS: This randomized clinical crossover study included 20 subjects with mild to moderate gingivitis. The study was conducted over a total examination period of 20 days with a wash-out period of 2 weeks between the use of both the toothpastes. The plaque index and gingival index of the study subjects were recorded at the designated time intervals throughout the study period.

STATISTICAL ANALYSIS: The data collected were entered on Microsoft Excel, and statistical analysis using SPSS software (SPSS version 28, IBM Corp, Armonk, New York, United States) was done. The statistical test used was the Wilcoxon signed-rank test. Moreover, p ≤0.05 was considered significant.

RESULTS: The results showed that the reduction in mean gingival index scores from baseline to day 3 was more statistically significant in the moringa-based dentifrice. Similarly, the plaque index scores showed statistically significant reduction following the use of the moringa-based dentifrice when compared with the miswak dentifrice. This study reveals that the moringa dentifrice is a safe and effective agent in reducing plaque accumulation and treating gingival inflammation.

CONCLUSION: The current study aims to provide an insight into the possible role of moringa dentifrice as a possible adjunctive oral hygiene aid.

PMID:35016231 | DOI:10.1055/s-0041-1736418

Clin Infect Dis. 2022 Jan 7:ciab1029. doi: 10.1093/cid/ciab1029. Online ahead of print.

ABSTRACT

BACKGROUND: The degree to which the 2019 novel coronavirus disease (COVID-19) pandemic will affect the US human immunodeficiency virus (HIV) epidemic is unclear.

METHODS: We used the Johns Hopkins Epidemiologic and Economic Model to project HIV infections from 2020 to 2025 in 32 US metropolitan statistical areas (MSAs). We sampled a range of effects of the pandemic on sexual transmission (0-50% reduction), viral suppression among people with HIV (0-40% reduction), HIV testing (0-50% reduction), and pre-exposure prophylaxis use (0-30% reduction), and indexed reductions over time to Google Community Mobility Reports.

RESULTS: Simulations projected reported diagnoses would drop in 2020 and rebound in 2021 or 2022, regardless of underlying incidence. If sexual transmission normalized by July 2021 and HIV care normalized by January 2022, we projected 1,161 (1%) more infections from 2020 to 2025 across all 32 cities than if COVID had not occurred. Among “optimistic” simulations in which sexual transmission was sharply reduced and viral suppression was maintained we projected 8% lower incidence (95% credible interval: 14% lower to no change). Among “pessimistic” simulations where sexual transmission was largely unchanged but viral suppression fell, we projected 11% higher incidence (1% to 21% higher). MSA-specific projections are available at jheem.org?covid.

CONCLUSIONS: The effects of COVID-19 on HIV transmission remain uncertain and differ between cities. Reported diagnoses of HIV in 2020-2021 are likely to correlate poorly with underlying incidence. Minimizing disruptions to HIV care is critical to mitigating negative effects of the COVID-19 pandemic on HIV transmission.

PMID:35016216 | DOI:10.1093/cid/ciab1029